Комментариев нет
DRT2-ROS16 Relay output Terminal I/O terminal enhances maintenance capabilities due replaceable relays. • Smart DeviceNet slave that provides preventive maintenance and trouble shooting information • 3A replaceable relays • Relays replaced easily, without special tools needed • Units can be extended with the XWT I/O blocks, reducing the number of network nodes required ...
Узнать больше »
Комментариев нет
DRT2-ID16S(-1) Sensor Connector Terminals New slave equipped with industry-standard e-con sensor connectors • Equipped with the standard Smart Slave functions for preventive maintenance and troubleshooting. Digital I/O Terminal compatible with industry-standard e-con sensor connectors. • Connect sensors easily without special tools. Reduce time required for wiring. ...
Узнать больше »
Комментариев нет
DRT2-AD04/-DA02 Analog I/O Terminals Calculations on Analog Values Can Be Performed within the Slave Itself • Equipped with the standard Smart Slave functions for preventive maintenance and troubleshooting. • Equipped with functions such as the scaling function, peak/bottom hold; top/valley hold; comparator function, cumulative counter, and rate of change. • Two I/O values can be allocated ...
Узнать больше »
Комментариев нет
DRT2-D08C(-1)/-D16C(-1) Harsh Environment Terminals Environment-resistive (IP67) I/O terminals with fault-detection and maintenance functions • Equipped with the standard Smart Slave functions for preventive maintenance and troubleshooting. • Conforms to IP67 standards. The terminal housing is also oil- and spatter-resistant. • The DeviceNet power supply is used by input devices to power ...
Узнать больше »
Комментариев нет
DRT2-D16(-1) Digital I/O Terminals I/O Device with DC-inputs and transistor outputs. • Maintenance data can be collected without affecting the functionality of the control system. • Valuable information can be collected and managed through the network, including information on the communications power supply voltage level, unit wear and tear, and equipment operating information. • Easily ...
Узнать больше »
Комментариев нет
GT1-CT01 Counter Unit Counter unit supporting encoder input • High-speed pulse with counting speeds up to 50 kHz. • Counting can be set to a multiplication factor of 1 or 4. • Wide range of measurement: –8,388,608 to 8,388,607. • One external input and two external outputs are available. • DIN rail mounting. ...
Узнать больше »
Комментариев нет
GT1-TS04 Temperature Input Units Temperature input units • Four inputs. • Two different models are available. One for thermocouples and one for platinum resistance thermometer. • Conversion time is only 250 ms for 4 inputs. • The DeviceNet configurator can be used to calibrate temperature inputs.. • The electorinic circuit section can be removed, so there is no need to disconnect ...
Узнать больше »
Комментариев нет
GT1-AD/-DA Analog I/O Units Analog input units • Available either with screw terminals or easy to use connectors (GT1-AD08MX) • 8 or 4 inputs • High resolution: 1/6,000 • High conversion speed: 8 ms/8 points or 4 ms/4 points. • DIN rail mounting. Analog output units Available either with screw terminals or easy to use connectors (GT1-DA04MX) • 4 inputs • High resolution: 1/6,000. • ...
Узнать больше »
Комментариев нет
GT1-ROS16/-ROP08/-FOP08 Relay Output Units Relay output units • 8- and 16-point relay output models are available. • Either 2, or 5 Amp maximum • DIN rail mounting. ...
Узнать больше »
Комментариев нет
GT1-ID/OD Digital I/O Units Digital I/O units • Several connectivity methods are available: - screw terminal - sensor connector - high-density connector • The screw terminal models have a detachable I/O electronic ciruits block that can be removed for maintenance purposes. • DIN rail mounting ...
Узнать больше »
