Комментариев нет
DRT1-D0CL(-1) Waterproof Terminals Economical Waterproof Terminals Available in 8 Different Models • Reduced Labor Connectors eliminate the need for connection tools. • Reduced Wiring The Terminals can be mounted closer to Sensors and so less wiring is required for signal lines. • Relay Box Not Required Waterproof, dust-tight, drip-proof construction (IP67) enables direct, on-site mounting. • ...
Узнать больше »
Комментариев нет
DRT1-TS04@ Temperature Input Terminals Measure temperatures. A wide range of temperature sensors is supported • Four inputs • Models for platinum resistance thermometers or thermocouples are available. • Incorporating wire burnout detecting function. • All inputs are insulated to one another. ...
Узнать больше »
Комментариев нет
3-tier Connection Terminals OMRON DRT1-D16T(-1) These new I/O Terminals have a 3-tier Terminal Block (16 I/O points). Six models are available: Input Terminals, I/O Terminals, and Output Terminals with NPN and PNP variations. Simplified wiring (Wires do not need be wired to the same terminal and terminal locations are clearer.) Reduced design and wiring time. Uses detachable cassette-type circuit ...
Узнать больше »
Комментариев нет
DRT1-D08(-1)/-MD16 8 Points I/O Terminals Compact 8-point and 16-point Transistorized Terminals • Compact (8-point models: 125 x 40 x 50 mm (W x H x D), 16-point models: 150 x 40 x 50 mm (W x H x D)) • Two independent power supplies can be used because the I/O terminals are insulated from the internal circuits. • DIN rail mounting and screw mounting are available. • Approved by ...
Узнать больше »
Комментариев нет
DRT2-ROS16 Relay output Terminal I/O terminal enhances maintenance capabilities due replaceable relays. • Smart DeviceNet slave that provides preventive maintenance and trouble shooting information • 3A replaceable relays • Relays replaced easily, without special tools needed • Units can be extended with the XWT I/O blocks, reducing the number of network nodes required ...
Узнать больше »
Комментариев нет
DRT2-ID16S(-1) Sensor Connector Terminals New slave equipped with industry-standard e-con sensor connectors • Equipped with the standard Smart Slave functions for preventive maintenance and troubleshooting. Digital I/O Terminal compatible with industry-standard e-con sensor connectors. • Connect sensors easily without special tools. Reduce time required for wiring. ...
Узнать больше »
Комментариев нет
DRT2-AD04/-DA02 Analog I/O Terminals Calculations on Analog Values Can Be Performed within the Slave Itself • Equipped with the standard Smart Slave functions for preventive maintenance and troubleshooting. • Equipped with functions such as the scaling function, peak/bottom hold; top/valley hold; comparator function, cumulative counter, and rate of change. • Two I/O values can be allocated ...
Узнать больше »
Комментариев нет
DRT2-D08C(-1)/-D16C(-1) Harsh Environment Terminals Environment-resistive (IP67) I/O terminals with fault-detection and maintenance functions • Equipped with the standard Smart Slave functions for preventive maintenance and troubleshooting. • Conforms to IP67 standards. The terminal housing is also oil- and spatter-resistant. • The DeviceNet power supply is used by input devices to power ...
Узнать больше »
Комментариев нет
DRT2-D16(-1) Digital I/O Terminals I/O Device with DC-inputs and transistor outputs. • Maintenance data can be collected without affecting the functionality of the control system. • Valuable information can be collected and managed through the network, including information on the communications power supply voltage level, unit wear and tear, and equipment operating information. • Easily ...
Узнать больше »
Комментариев нет
GT1-CT01 Counter Unit Counter unit supporting encoder input • High-speed pulse with counting speeds up to 50 kHz. • Counting can be set to a multiplication factor of 1 or 4. • Wide range of measurement: –8,388,608 to 8,388,607. • One external input and two external outputs are available. • DIN rail mounting. ...
Узнать больше »
